Select your vehicle Select your vehicle

Select your vehicle
2JZGTE BCC Boost Cut Controller Device Replacement for GReddy

2JZGTE BCC Boost Cut Controller Device Replacement for GReddy

These are once again available as of 2021!! Usually ships within a day or two

This Boost Cut Control Device, or BCCD for short, was developed to allow the 1993-up Supra Turbo to run over 14.7psi of boost without hitting fuel cut. Unlike other boost cut control devices that are either discontinued or skew voltage output (and thus can affect other systems that reference the stock MAP sensor for operation), this BCCD allows the voltage to pass through undisturbed until it hits the predetermined 4.1V or 4.3V. Then, it caps and holds the voltage at 4.1 or 4.3V. This allows all of your Supra's factory systems such as 9-12V fuel pump operation, turbocharger transition and pre-spool, and other things to operate like normal, but will still allow the car to run over 14.7psi of boost without fuel cut! Some additional features include:

* Settings for 4.1V or 4.3V depending on the year of your Supra. This is still adjustable if needed, but simplifies things for the average installer. No need to go through the tuning process, just install it!

* Double side tape pre-applied. We recommend soldering these in, and therefore do not include any crimp connectors.

* A red LED light is visible through the wire hole to show that the unit is functioning properly.

* The instructions are the EXACT same as other boost and fuel cut controllers for the MKIV Supra Turbo, as our BCCD even has the same color wires as other popular boost cut controllers.

* Very compact 1.35" x 1.35" x 0.58" case makes installing it a breeze.

Unlike the original, detailed instructions are included in a nice PDF file when you order.

If you are installing this on a JDM Supra or other speed density based ECU which does NOT use a Mass Air Flow meter from the factory, then you will need some sort of piggyback fuel injector controller such as E-Manage, AEM FIC, or similar; otherwise when this BCCD caps the voltage of the MAP sensor, the stock ECU will not know the true manifold pressure reading, thus causing problems.

If you need installation instructions, please let us know and we will be happy to send some!

Please note that this will work on both 1JZ and 2JZ GTE setups. USDM 2JZGTE, JDM 2JZGTE, 2JZGTE VVTi, and 1JZ non-VVTi. We strongly advise using a piggyback especially in conjunction with JDM engines that are MAP based only, as the ECU will not know how much boost it is getting over 14.5 psi

The genuine GReddy SW20 boxes have been discontinued for over 10 years. This replacement works exactly the same way, uses the same colored wires, and we have been selling them for the entire time. You should have no issues with this.

Not rated yet
0
  • $131
 
OR
    • SKU
      MVPbcc
    • Weight
      1 lbs

Most product ships from either the manufacture or largest wholesale location to pass the saving to you. Most orders will ship via UPS, as we will be able to provide the best rates and have had the least issues when using UPS.


IF YOU DO NOT LIKE THE AUTOMATED SHIPPING CALCULATOR'S RATES, PLEASE CONTACT US AND WE CAN GET YOU A BETTER ONE! Especially for anyone outside the USA, please contact us with a list of parts you'd like to order, and where you are located.

We accept the following payment methods:

Also Venmo and unmarked nonsequential dollar bills

  • Fitment Type
    Vehicle Specific
MakeModelYearSubmodel
Toyota/LexusLexus GS/Aristo1992-1997 S1472JZ-GE/2JZ-GTE 3.0 I6
Toyota/LexusLexus GS/Aristo1998-2005 S1602JZGE/2JZGTE 3.0 I6 (98-05) JZS160/JZS161
Toyota/LexusLexus IS/Altezza1998-2005IS300 2JZGE 3.0 I6 JCE10
Toyota/LexusSupra1993-2002 A802JZ-GTE/2JZ-GE 3.0 I6 JZA80
Toyota/LexusSupra1986.5-1992 A701JZ-GTE 2.5 TT I6 JDM 1990-1993 JZA70

Footer navigation