Nissan 350Z/370Z 6 Speed (CD009, JK40C, etc.)

This is it: the holy grail of clutches for a big power 1UZ swap! This clutch is a 7.25" rally twin disc button clutch that can hold over 800HP and weighs less than an OEM type clutch INCLUDING the flywheel and spacer plate!! Clutch assembly with button flywheel weighs just 16.75 lbs

This clutch is 100% made for the UZ swap, no modified flywheel or clutch setup. When we decided to build the ultimate clutch for our V8 swap, we looked to the industry leader and manufacturing giant that is QuarterMaster. They have been supplying NASCAR for years, so there is no better place to get the best product from.

This clutch kit comes with the following:

• XAT QM flywheel
• XAT QM 7.25 V-Drive 2 plate clutch pack
• ARP hardware to install the clutch to engine
• XAT billet spacer plate (configured to trans type in drop down menu)

If you need the OEM starter gear and shim, you can select that from our drop down menu as well. For the complete setup please select the QMI throw-out bearing kit as well.  One bad clutch for one bad swap!

This is a complete kit, with twin disc clutch assembly, install kit (ARP flywheel bolts, clutch hardware), button flywheel, and spacer as needed. 

Which engine? Which transmission? All of them! 

We have a version for your JZ, UZ, or GZ engine, with Z33 / Z34 trans, R154, V160, or W58! The twin disc is recommended for 800rwhp cars for street/drift/endurance. The sintered metallic compound is one of the highest quality materials for clutches. This clutch has slots between the segments to help cool the clutch easier, and extra thick padding to last through an extreme amount of abuse! 

All feedback for this clutch from our many customers over the years has been overwhelmingly positive. Clutch pedal isnt overly aggressive, it can still slip for street driving, yet has no problem holding gobs of power. Here at XAT, we often measure power in gobs. This kit holds "many" gobs. This is the QMI 8.5 inch version we recommend most for street driven cars. 

The starter gear includes the ring gear needed to start the car. The much smaller button flywheel has much less rotating mass to deal with and works very well, but has no starter motor engagement. The base kit includes the button flywheel, with an option to have a full size flywheel and clutch combo. The assembled RaceLyte clutch and flywheel weighs 22 lbs 14 oz. 

If this is your first time with an XAT clutch conversion, you will need the starter gear as well. Otherwise you can opt for the full size street flywheel instead and not need the starter gear or the button flywheel. You will need to use a 3/4" master cylinder in tandem with the TOB we use.

For this setup, XAT started completely from scratch, as nothing beats a purpose built billet part from the ground up! As we continue to partner up and offer more and more options for the increasingly popular Nissan 350Z/370Z 6 speed-known to handle over 800 HP at the wheels without opening it up, we continue to bring custom bespoke and billet parts to replace the aged V160 and R154 options. 

These Nissan trannies have been proven that they are a stout and reliable trans that is inexpensive, readily available, and will be for many years to come. Although the early years proved to be troublesome with the CD001, CD003, and CD005 transmissions, by the CD008 and CD009 revisions, shifting has been improved, smoothed out, and solidified. The newer JK40C 370Z transmissions are also reported to have the same internals carried over from the CD009. 

This will fit all versions of this transmission: CD001, CD003, CD005, CD008, CD009, JK41A, JK41B, JK40C, 1EA0A, and 1EA0B Our light weight flywheel is infinitely rebuildable with replaceable friction surface disc, and at just under 14 lbs, it feels right at home both on the street and at the track. Flywheel bolts get torqued to 80 ft lbs. Dont forget to do so in a cross pattern! Single disc clutch options will be anything "off the shelf" that fits the 300ZX twin turbo (Z32). 

Please email us if you have ANY questions or need assistance with choosing the right clutch for your build! 

** We sell clutch kits to fit this flywheel, ready to go! ** 

As a quick recap: You will need the 1UZ, 2UZ, or early 3UZ 4 speed or 5 speed automatic bellhousing. The 6 speed automatic transmission bellhousing will NOT fit, as the 6 speed used a different bolt pattern.

We also have twin disc QuarterMaster clutches (7.25" and 8.5" twin disc) and flywheels. We offer a QM throw out bearing for fitment. The twin disc clutch kits do NOT use this flywheel, they use a "button flywheel" instead.

When we took a look at the previous generation of adapter plates, all we could see was room for improvement and higher quality. We wanted a plate that would mount PERFECTLY with zero slop. It needed to look good and perform even better. DON'T get stuck with an overvalued, sloppy plate that ends up costing you input shafts and has poor fitment. You can go with a less expensive alternative and end up with broken parts, or you can do it right the first time with us! No complaints with over 5 years of service.

This billet aluminum adapter plate reuses your automatic J3 bellhousing (usually from 2JZGTE A340E automatics).Alignment of the input shaft becomes dependent on this plate and not the quality of the bell housing cut, so worry not! This isn't like other kits out there. The J2 bellhousing will not work 

Regardless of which clutch you use, you will need to use the Quarter Master throw out bearing. 

With single disc clutch setups, this kit is designed to use our custom flywheel that uses off the shelf "Z32 turbo" (89-96 Nissan 300ZX twin turbo) clutches, which are inexpensive, readily available, and hold power well. 

Please see the listing below for the flywheel needed. Please note that with a single disc clutch, this requires a proprietary flywheel. OUR "OEM STYLE" AND "LIGHTWEIGHT" XAT FLYWHEELS WILL NOT WORK WITH THIS TRANSMISSION. You will need the specific CD009 flywheel made for this application.

The twin disc setups include their own flywheel, but will also need a ring gear for the starter (the OEM auto flex plate). 

Included with purchase on this listing:

• Adapter plate with hardware to install
• Quill tube for mounting the hydraulic throw out bearing
• Pilot bushing adapter, with bushing installed
• Throw out bearing (optionally)

XAT Racing took a hard look at the concept, and decided to go all in with the "Toyota Big-Block" design. These V12s have started becoming more popular over the past few years! This will fit all versions of this transmission: CD001, CD003, CD005, CD008, CD009, JK41A, JK41B, JK40C, 1EA0A, and 1EA0B from the 2003-2008 Nissan 350Z/Fairlady Z, 2009-2020 370Z, Skyline V35 and V36 non-GTR sedan and coupe, and Infiniti G35 and G37 

Our products are CAD designed with OEM blocks and transmissions on professional equipment by industry professionals. No bad measurements, no flame cuts, no warped discs, no nonsense. You should be using a 3/4" master cylinder in tandem with the TOB we use.

This is the missing link for doing a 1UZFE swap, or simply adding a manual transmission to your Toyota V8. Our CNC process for manufacturing the plate results in an extremely precise adapter plate, laser tight tolerances, and a focus on quality that has yielded a product that will produce less wear on the transmission and clutch. The adapter kits come with the needed pilot adapter and bushing as well. This is the tried and true kit from XAT Racing, except no imitations when it comes to Toyota JZs 

Click here for install instructions

You can also use the less expensive RAM throw out bearing with this kit, however we do not support it. You will need to drill and tap the plate at your own risk to mount one.

Looking for a clutch for this adapter plate? 

When we took a look at the previous generation of adapter plates, all we could see was room for improvement and higher quality. We wanted a plate that would mount PERFECTLY with zero slop. It needed to look good and perform even better. DON'T get stuck with an overvalued, sloppy plate that ends up costing you input shafts and has poor fitment. You can go with a less expensive alternative and end up with broken parts, or you can do it right the first time with us! No complaints with over 5 years of service.

This billet aluminum adapter plate reuses your factory 4 speed or 5 speed auto UZ bellhousing (1990-2004). It will require you to cut off the CD009 bellhousing, which gives MUCH more room to work with in most chassis. Alignment of the input shaft becomes dependent on this plate and not the quality of the bell housing cut, so worry not! This isn't like other kits out there. 

2005+ 6 speed auto bellhousings will not fit with this adapter. 

Regardless of which clutch you use, you will need to use the Quarter Master throw out bearing. 

With single disc clutch setups, this kit is designed to use our custom flywheel that uses off the shelf "Z32 turbo" (89-96 Nissan 300ZX twin turbo) clutches, which are inexpensive, readily available, and hold power well. 

Please see the listing below for the flywheel needed. Please note that with a single disc clutch, this requires a proprietary flywheel. OUR "OEM STYLE" AND "LIGHTWEIGHT" XAT FLYWHEELS WILL NOT WORK WITH THIS TRANSMISSION. You will need the specific CD009 flywheel made for this application.

The twin disc setups include their own flywheel, but will also need a ring gear for the starter (the OEM auto flex plate). 

Included with purchase on this listing:

• Adapter plate with hardware to install
• Quill tube for mounting the hydraulic throw out bearing
• Pilot bushing adapter, with bushing installed
• Throw out bearing (optionally)

XAT Racing took a hard look at the concept, and decided to go all in with the "Toyota Big-Block" design. These V12s have started becoming more popular over the past few years! This will fit all versions of this transmission: CD001, CD003, CD005, CD008, CD009, JK41A, JK41B, JK40C, 1EA0A, and 1EA0B from the 2003-2008 Nissan 350Z/Fairlady Z, 2009-2020 370Z, Skyline V35 and V36 non-GTR sedan and coupe, and Infiniti G35 and G37 

Our products are CAD designed with OEM blocks and transmissions on professional equipment by industry professionals. No bad measurements, no flame cuts, no warped discs, no nonsense. You should be using a 3/4" master cylinder in tandem with the TOB we use.

This is the missing link for doing a 1UZFE swap, or simply adding a manual transmission to your Toyota V8. Our CNC process for manufacturing the plate results in an extremely precise adapter plate, laser tight tolerances, and a focus on quality that has yielded a product that will produce less wear on the transmission and clutch. The adapter kits come with the needed pilot adapter and bushing as well. This is the tried and true kit from XAT Racing, except no imitations when it comes to Toyota V8s 

Click here for install instructions

You can also use the less expensive RAM throw out bearing with this kit, however we do not support it. You will need to drill and tap the plate at your own risk to mount one.

Looking for a clutch for this adapter plate? 

Does NOT require a ring gear! Bolt up your factory flex plate! Uses any off the shelf Z32 Nissan 300ZX TT single disc clutch with any 350Z/370Z transmission application!

Quick version of what you'll need:

• T56 style throw out bearing
• Pilot bushing adapter (included with transmission adapter)
• Nissan 6 speed
• Our flywheel (no other ones will work)
• 300ZX TT clutch
• 3UR serviceable bellhousing with 12 bolt trans flange

Quick version of what you'll need:

• T56 style throw out bearing
• Pilot bushing adapter (included)
• Nissan 6 speed (CD001, CD003, CD005, CD008, CD009, CD00A, JK41A, JK41B, JK40C, 1EA0A, or 1EA0B)
• Our flywheel (no other ones will work)
• 300ZX TT clutch Z32 twin turbo
• 1UR removeable bellhousing with 12 bolt trans-side flange

When we took a look at the previous generation of adapter plates, all we could see was room for improvement and higher quality. We wanted a plate that would mount PERFECTLY with zero slop. It needed to look good and perform even better. DON'T get stuck with an overvalued, sloppy plate that ends up costing you input shafts and has poor fitment. You can go with a less expensive alternative and end up with broken parts, or you can do it right the first time with us! No complaints with over 5 years of service.

This billet aluminum adapter plate reuses your factory 4 speed auto 1GZ bellhousing (1997-2004). It will require you to cut off the CD009 bellhousing, which gives MUCH more room to work with in most chassis. Alignment of the input shaft becomes dependent on this plate and not the quality of the bell housing cut, so worry not! This isn't like other kits out there. 

2005-2017 bellhousings will not fit with this adapter. Although the GR-to-CD009 adapter plate we offer would bolt up, the thickness spacing is still wrong

Regardless of which clutch you use, you will need to use the Quarter Master throw out bearing. 

With single disc clutch setups, this kit is designed to use our custom flywheel that uses off the shelf "Z32 turbo" (89-96 Nissan 300ZX twin turbo) clutches, which are inexpensive, readily available, and hold power well. 

Please see the listing below for the flywheel needed. Please note that with a single disc clutch, this requires a proprietary flywheel. OUR "OEM STYLE" AND "LIGHTWEIGHT" XAT FLYWHEELS WILL NOT WORK WITH THIS TRANSMISSION. You will need the specific CD009 flywheel made for this application.

The twin disc setups include their own flywheel, but will also need a ring gear for the starter (the OEM auto flex plate). 

Included with purchase on this listing:

• Adapter plate with hardware to install
• Quill tube for mounting the hydraulic throw out bearing
• Pilot bushing adapter, with bushing installed
• Throw out bearing (optionally)

XAT Racing took a hard look at the concept, and decided to go all in with the "Toyota Big-Block" design. These V12s have started becoming more popular over the past few years! This will fit all versions of this transmission: CD001, CD003, CD005, CD008, CD009, JK41A, JK41B, JK40C, 1EA0A, and 1EA0B from the 2003-2008 Nissan 350Z/Fairlady Z, 2009-2020 370Z, Skyline V35 and V36 non-GTR sedan and coupe, and Infiniti G35 and G37 

Our products are CAD designed with OEM blocks and transmissions on professional equipment by industry professionals. No bad measurements, no flame cuts, no warped discs, no nonsense. You should be using a 3/4" master cylinder in tandem with the TOB we use.

This is the missing link for doing the 1GZFE swap, or simply adding a manual transmission to your already badass Toyota Century. Our CNC process for manufacturing the plate results in an extremely precise adapter plate, laser tight tolerances, and a focus on quality that has yielded a product that will produce less wear on the transmission and clutch. The adapter kits come with the needed pilot adapter and bushing as well. This is the tried and true kit from XAT Racing, except no imitations when it comes to Toyota V12 1GZs. Sorry, V12 not included.

You can also use the less expensive RAM throw out bearing with this kit, however we do not support it. You will need to drill and tap the plate at your own risk to mount one.

Click here for install instructions

Looking for a clutch for this adapter plate? 

XAT Racing Toyota Lexus 1GZ V12 Lightweight Billet Aluminum 13.5 lb Flywheel for CD009 Nissan Infiniti 6 speed 350Z 370Z G35 G37 Manual Transmission Swaps

For this setup, XAT started completely from scratch, as nothing beats a purpose built billet part from the ground up! As we continue to partner up and offer more and more options for the increasingly popular Nissan 350Z/370Z 6 speed-known to handle over 800 HP at the wheels without opening it up, we continue to bring custom bespoke and billet parts to replace the aged V160 and R154 options. 

These Nissan trannies have been proven that they are a stout and reliable trans that is inexpensive, readily available, and will be for many years to come. Although the early years proved to be troublesome with the CD001, CD003, and CD005 transmissions, by the CD008 and CD009 revisions, shifting has been improved, smoothed out, and solidified. The newer JK40C 370Z transmissions are also reported to have the same internals carried over from the CD009. 

This will fit all versions of this transmission: CD001, CD003, CD005, CD008, CD009, JK41A, JK41B, JK40C, 1EA0A, and 1EA0B Our light weight flywheel is infinitely rebuildable with replaceable friction surface disc, and at just under 14 lbs, it feels right at home both on the street and at the track. Flywheel bolts get torqued to 80 ft lbs. Dont forget to do so in a cross pattern! Single disc clutch options will be anything "off the shelf" that fits the 300ZX turbo (Z32). 

Please email us if you have ANY questions or need assistance with choosing the right clutch for your build! 

** We sell clutch kits to fit this flywheel, ready to go! ** 

As a quick recap: You will need the JZ J3 automatic bellhousing, as well as our adapter kit (or SupraStore's), if you haven't converted already. We also have twin disc QuarterMaster clutches (7.25" and 8.5" twin disc) and flywheels. We offer a QM throw out bearing for fitment. The twin disc clutch kits do NOT use this flywheel, they use a "button flywheel" instead.