Search

Mishimoto Radiator Hose Kit S13 S14 240SX 180SX Silvia KA24 

Mishimoto Aluminum Fan Shroud Kit Nissan S13 S14 240SX Silvia

Tomei Technical Trax Advance T-Trax LSD 2-Way Limited Slip Differential

This XAT flywheel is perfect for those who want a simple and straightforward flywheel for a manual conversion on their Toyota/Lexus V8. Affordable cast flywheel with OEM quality and OEM ring gear. 

Excellent for starter projects and conversions, as well as daily street driving. This flywheel weighs 20 lbs 4 oz. Looking for a bit more performance and less rotating mass? 

Check out the 13 lb XAT Chromoly Flywheel instead!! Our flywheel utilizes the proven torque holding clutches of the SW20 MR2 TURBO 3S-GTE. We offer clutch setups to suit everything from a stock engine all the way up to 680 FT/LBS with this flywheel! 

For installation when using the optional ARP bolt kit, torque to 70 FT/LBS using red thread locker/loctite on the bolts, and tightening in a star pattern, not one next to the other. We also recommend tightening down in 2 or 3 passes as well, instead of going from finger tight straight to 70 ft lbs. This flywheel does NOT require any spacers to bolt on, not even the factory spacer that goes from the crankshaft to the factory flex plate.

This flywheel is meant for our W55/W58, R150/R151, R154, KA, and SR transmission adapters. This will NOT work with our CD009 / JK series Nissan 6 speed adapter! Also not meant to fit international H151 models

Solve your fuel delivery woes with our new and improved V3 hanger for a Nissan S14, S15, R33, R34! In past versions we provided you with a only fuel bulkhead, you needed to solve your in tank pump bracketry. This is now a complete solution, including bracketry for your pumps and fuel level sender leaving you with a hassle free install.

This hanger is compatible with 3 types of Walbro pumps, able provide you with enough fuel flow for 1300hp+ 

All components in this kit are rated for Ethanol (E85) Fuel

A integrated jet pump design makes sure you still maintain full-capacity usage of your saddle-style gas tank.

Bulkhead wiring is provided not only for pump power but also your fuel level sender. So you maintain all OEM functionality to your dash gauges.

When we took a look at the previous generation of adapter plates, all we could see was room for improvement and higher quality. We wanted a plate that would mount PERFECTLY with zero slop. It needed to look good and perform even better. DON'T get stuck with an overvalued, sloppy plate that ends up costing you input shafts and has poor fitment. You can go with a less expensive alternative and end up with broken parts, or you can do it right the first time with us! No complaints with over 5 years of service.

This billet aluminum adapter plate reuses your factory 4 speed auto 1GZ bellhousing (1997-2004). It will require you to cut off the CD009 bellhousing, which gives MUCH more room to work with in most chassis. Alignment of the input shaft becomes dependent on this plate and not the quality of the bell housing cut, so worry not! This isn't like other kits out there. 

2005-2017 bellhousings will not fit with this adapter. Although the GR-to-CD009 adapter plate we offer would bolt up, the thickness spacing is still wrong

Regardless of which clutch you use, you will need to use the Quarter Master throw out bearing. 

With single disc clutch setups, this kit is designed to use our custom flywheel that uses off the shelf "Z32 turbo" (89-96 Nissan 300ZX twin turbo) clutches, which are inexpensive, readily available, and hold power well. 

Please see the listing below for the flywheel needed. Please note that with a single disc clutch, this requires a proprietary flywheel. OUR "OEM STYLE" AND "LIGHTWEIGHT" XAT FLYWHEELS WILL NOT WORK WITH THIS TRANSMISSION. You will need the specific CD009 flywheel made for this application.

The twin disc setups include their own flywheel, but will also need a ring gear for the starter (the OEM auto flex plate). 

Included with purchase on this listing:

• Adapter plate with hardware to install
• Quill tube for mounting the hydraulic throw out bearing
• Pilot bushing adapter, with bushing installed
• Throw out bearing (optionally)

XAT Racing took a hard look at the concept, and decided to go all in with the "Toyota Big-Block" design. These V12s have started becoming more popular over the past few years! This will fit all versions of this transmission: CD001, CD003, CD005, CD008, CD009, JK41A, JK41B, JK40C, 1EA0A, and 1EA0B from the 2003-2008 Nissan 350Z/Fairlady Z, 2009-2020 370Z, Skyline V35 and V36 non-GTR sedan and coupe, and Infiniti G35 and G37 

Our products are CAD designed with OEM blocks and transmissions on professional equipment by industry professionals. No bad measurements, no flame cuts, no warped discs, no nonsense. You should be using a 3/4" master cylinder in tandem with the TOB we use.

This is the missing link for doing the 1GZFE swap, or simply adding a manual transmission to your already badass Toyota Century. Our CNC process for manufacturing the plate results in an extremely precise adapter plate, laser tight tolerances, and a focus on quality that has yielded a product that will produce less wear on the transmission and clutch. The adapter kits come with the needed pilot adapter and bushing as well. This is the tried and true kit from XAT Racing, except no imitations when it comes to Toyota V12 1GZs. Sorry, V12 not included.

You can also use the less expensive RAM throw out bearing with this kit, however we do not support it. You will need to drill and tap the plate at your own risk to mount one.

Looking for a clutch for this adapter plate? 

When we took a look at the previous generation of adapter plates, all we could see was room for improvement and higher quality. We wanted a plate that would mount PERFECTLY with zero slop. It needed to look good and perform even better. DON'T get stuck with an overvalued, sloppy plate that ends up costing you input shafts and has poor fitment. You can go with a less expensive alternative and end up with broken parts, or you can do it right the first time with us! No complaints with over 5 years of service.

This billet aluminum adapter plate reuses your automatic 1UZ, 2UZ or 3UZ bellhousing. (U1 or U2 from the 4 speed and 5 speed autos. 3UZ 6 speed bellhousing will not fit). It will require you to cut off the CD009 bellhousing, which gives MUCH more room to work with in most chassis. Alignment of the input shaft becomes dependent on this plate and not the quality of the bell housing cut, so worry not! This isn't like other kits out there. This will also fit 2UZs, though the kit was designed to use the U1 bellhousing specifically.

Regardless of which clutch you use, you will need to use the Quarter Master throw out bearing. 

With single disc clutch setups, this kit is designed to use our custom flywheel that uses off the shelf "Z32 turbo" (89-96 Nissan 300ZX twin turbo) clutches, which are inexpensive, readily available, and hold power well. 

Please see the listing below for the flywheel needed. Please note that with a single disc clutch, this requires a proprietary flywheel. OUR "OEM STYLE" AND "LIGHTWEIGHT" XAT FLYWHEELS WILL NOT WORK WITH THIS TRANSMISSION. You will need the specific CD009 flywheel made for this application.

The twin disc setups include their own flywheel, but will also need a ring gear for the starter (the OEM auto flex plate). 

Included with purchase on this listing:

• Adapter plate with hardware to install
• Quill tube for mounting the hydraulic throw out bearing
• Pilot bushing adapter, with bushing installed
• Throw out bearing (optionally)

XAT Racing took a hard look at the concept, and decided to go all in with the "Toyota Small-Block" design. These V8s have started becoming overwhelmingly popular over the past few years! This will fit all versions of this transmission: CD001, CD003, CD005, CD008, CD009, JK41A, JK41B, JK40C, 1EA0A, and 1EA0B from the 2003-2008 Nissan 350Z/Fairlady Z, 2009-2020 370Z, Skyline V35 and V36 non-GTR sedan and coupe, and Infiniti G35 and G37 

Our products are CAD designed with OEM blocks and transmissions on professional equipment by industry professionals. No bad measurements, no flame cuts, no warped discs, no nonsense. You should be using a 3/4" master cylinder in tandem with the TOB we use.

This is the missing link for doing the 1UZFE, 2UZFE, or 3UZFE swap, or simply adding a manual transmission to your already existing UZ powered vehicle (LS400, SC400, and GS400 included). Our CNC process for manufacturing the plate results in an extremely precise adapter plate, laser tight tolerances, and a focus on quality that has yielded a product that will produce less wear on the transmission and clutch. The kits being sold by our "competition" are routinely a few thousands off and have sloppy fitting dowel pin holes. We have even seen competitor's products first hand being warped right out of the box! The adapter kits come with the needed pilot adapter and bushing as well. This is the tried and true kit from XAT Racing, except no imitations when it comes to 1UZs..

You can also use the less expensive RAM throw out bearing with this kit, however we do not support it. You will need to drill and tap the plate at your own risk to mount one.

You may also need other manual conversion parts, depending on your chassis. Please keep in mind you may need to use a 3/4" bore master cylinder with this kit. The factory master cylinder may be enough, however it will ultimately depend on your application. The majority of Toyota car manuals have a 5/8" bore master. The optional master cylinder we provide may require further chassis modification to bolt up to your firewall.

The GKTech shifter is great for relocating the shifter fit Lexus SC fitment and MkIV Supra fitment. Should also fit other applications as well, though that will depend on the chassis you're using and where the engine is mounted

Looking for a clutch for this adapter plate? 

When we took a look at the previous generation of adapter plates, all we could see was room for improvement and higher quality. We wanted a plate that would mount PERFECTLY with zero slop. It needed to look good and perform even better. DON'T get stuck with an overvalued, sloppy plate that ends up costing you input shafts and has poor fitment. You can go with a less expensive alternative and end up with broken parts, or you can do it right the first time with us! No complaints with over 5 years of service.

This billet aluminum adapter plate reuses your automatic J3 bellhousing (usually from 2JZGTE A340E automatics). It will require you to cut off the CD009 bellhousing, which gives MUCH more room to work with in most chassis. Alignment of the input shaft becomes dependent on this plate and not the quality of the bell housing cut, so worry not! This isn't like other kits out there. 

Regardless of which clutch you use, you will need to use the Quarter Master throw out bearing. 

With single disc clutch setups, this kit is designed to use our custom flywheel that uses off the shelf "Z32 turbo" (89-96 Nissan 300ZX twin turbo) clutches, which are inexpensive, readily available, and hold power well. 

Please see the listing below for the flywheel needed. Please note that with a single disc clutch, you will need the specific CD009 flywheel made for this application.

The twin disc setups include their own flywheel, but will retain the factory a ring gear for the starter (the OEM auto flex plate). 

Included with purchase on this listing:

• Adapter plate with hardware to install
• Quill tube for mounting the hydraulic throw out bearing
• Pilot bushing adapter, with bushing installed

XAT Racing took a hard look at the concept, and decided to go all in with the "Toyota Small-Block" design. These V8s have started becoming overwhelmingly popular over the past few years! This will fit all versions of this transmission: CD001, CD003, CD005, CD008, CD009, JK41A, JK41B, JK40C, 1EA0A, and 1EA0B from the 2003-2008 Nissan 350Z/Fairlady Z, 2009-2020 370Z, Skyline V35 and V36 non-GTR sedan and coupe, and Infiniti G35 and G37 

Our products are CAD designed with OEM blocks and transmissions on professional equipment by industry professionals. No bad measurements, no flame cuts, no warped discs, no nonsense. You should be using a 3/4" master cylinder in tandem with the TOB we use.

This is the missing link for doing the 1JZ or 2JZ swap, or simply adding a manual transmission to your already existing JZ powered vehicle (Supra, IS300, SC300, GS300). Our CNC process for manufacturing the plate results in an extremely precise adapter plate, laser tight tolerances, and a focus on quality that has yielded a product that will produce less wear on the transmission and clutch. The kits being sold by our "competition" are routinely a few thousands off and have sloppy fitting dowel pin holes. We have even seen competitor's products first hand being warped right out of the box! The adapter kits come with the needed pilot adapter and bushing as well. This is the tried and true kit from XAT Racing, except no imitations when it comes to doing it right the first time.

You can also use the less expensive RAM throw out bearing with this kit, however we do not support it. You will need to drill and tap the plate at your own risk to mount one.

The GKTech shifter is great for relocating the shifter fit Lexus SC fitment and MkIV Supra fitment. Should also fit other applications as well, though that will depend on the chassis you're using and where the engine is mounted

Looking for a clutch for this adapter plate? 

Mishimoto Radiator S13 S14 240SX 180SX Silvia