Search

ARP Flywheel Bolts for Custom XAT QM Clutches to Z33 Z34 Transmission

Tomei Technical Trax Advance T-Trax LSD 2-Way Limited Slip Differential for Manual Z33 350Z G35

When we took a look at the previous generation of adapter plates, all we could see was room for improvement and higher quality. We wanted a plate that would mount PERFECTLY with zero slop. It needed to look good and perform even better. DON'T get stuck with an overvalued, sloppy plate that ends up costing you input shafts and has poor fitment. You can go with a less expensive alternative and end up with broken parts, or you can do it right the first time with us! No complaints with over 5 years of service.

This billet aluminum adapter plate reuses your automatic J3 bellhousing (usually from 2JZGTE A340E automatics). It will require you to cut off the CD009 bellhousing, which gives MUCH more room to work with in most chassis. Alignment of the input shaft becomes dependent on this plate and not the quality of the bell housing cut, so worry not! This isn't like other kits out there. 

Regardless of which clutch you use, you will need to use the Quarter Master throw out bearing. 

With single disc clutch setups, this kit is designed to use our custom flywheel that uses off the shelf "Z32 turbo" (89-96 Nissan 300ZX twin turbo) clutches, which are inexpensive, readily available, and hold power well. 

Please see the listing below for the flywheel needed. Please note that with a single disc clutch, you will need the specific CD009 flywheel made for this application.

The twin disc setups include their own flywheel, but will retain the factory a ring gear for the starter (the OEM auto flex plate). 

Included with purchase on this listing:

• Adapter plate with hardware to install
• Quill tube for mounting the hydraulic throw out bearing
• Pilot bushing adapter, with bushing installed

XAT Racing took a hard look at the concept, and decided to go all in with the "Toyota Small-Block" design. These V8s have started becoming overwhelmingly popular over the past few years! This will fit all versions of this transmission: CD001, CD003, CD005, CD008, CD009, JK41A, JK41B, JK40C, 1EA0A, and 1EA0B from the 2003-2008 Nissan 350Z/Fairlady Z, 2009-2020 370Z, Skyline V35 and V36 non-GTR sedan and coupe, and Infiniti G35 and G37 

Our products are CAD designed with OEM blocks and transmissions on professional equipment by industry professionals. No bad measurements, no flame cuts, no warped discs, no nonsense. You should be using a 3/4" master cylinder in tandem with the TOB we use.

This is the missing link for doing the 1JZ or 2JZ swap, or simply adding a manual transmission to your already existing JZ powered vehicle (Supra, IS300, SC300, GS300). Our CNC process for manufacturing the plate results in an extremely precise adapter plate, laser tight tolerances, and a focus on quality that has yielded a product that will produce less wear on the transmission and clutch. The kits being sold by our "competition" are routinely a few thousands off and have sloppy fitting dowel pin holes. We have even seen competitor's products first hand being warped right out of the box! The adapter kits come with the needed pilot adapter and bushing as well. This is the tried and true kit from XAT Racing, except no imitations when it comes to doing it right the first time.

You can also use the less expensive RAM throw out bearing with this kit, however we do not support it. You will need to drill and tap the plate at your own risk to mount one.

The GKTech shifter is great for relocating the shifter fit Lexus SC fitment and MkIV Supra fitment. Should also fit other applications as well, though that will depend on the chassis you're using and where the engine is mounted

Looking for a clutch for this adapter plate? 

XAT QuarterMaster 1UZ Twin Clutch Kit

One of the better single disc clutch kits that you can buy for manual transmission swapped 1UZ, 2UZ, and 3UZ Toyota/Lexus V8 engines. This kit will handle big power, yet is still very streetable. 

Rated for 500 ft lbs of torque The flagship stage for a high powered street or race car that requires a manageable and friendly engagement, the stage 3+ features a carbon semi-metallic full faced material that offers unparalleled life, friction co-efficient and drivability characteristics in one single package. 

The hub is double sprung with spring cover relieves for flexibility and heat treated components for strength and durability. Great for street, drag, drift, autocross, road racing, pulling, rally and drift.

If you select Z33/Z34 fitment, we will provide you with the Z32TT clutch made to fit with our in house CD009 kits. We chose that clutch specifically to design the kit around. This is a different clutch from the 350Z/370Z clutch, even though you are using that transmission.

This is a complete kit, with twin disc clutch assembly, install kit (ARP flywheel bolts, clutch hardware), button flywheel, and spacer as needed. 

Which engine? Which transmission? All of them! 

We have a version for your UZ engine, with Z33 / Z34 trans, R154, V160, or W58! The twin disc is recommended for 800rwhp cars for street/drift/endurance. The sintered metallic compound is one of the highest quality materials for clutches. This clutch has slots between the segments to help cool the clutch easier, and extra thick padding to last through an extreme amount of abuse! 

All feedback for this clutch from our many customers over the years has been overwhelmingly positive. Clutch pedal isnt overly aggressive, it can still slip for street driving, yet has no problem holding gobs of power. Here at XAT, we often measure power in gobs. This kit holds "many" gobs. This is the 8.5 inch version we recommend most for street driven cars.

The starter gear includes the ring gear needed to start the car. The much smaller button flywheel has much less rotating mass to deal with and works very well, but has no starter motor engagement. The base kit includes the button flywheel, with an option to have a full size flywheel and clutch combo. The assembled RaceLite clutch and flywheel weighs 22 lbs 14 oz.

If this is your first time with an XAT clutch conversion, you will need the starter gear as well. Otherwise you can opt for the RaceLite flywheel instead and not need the starter gear or the button flywheel. You should be using a 3/4" master cylinder in tandem with the TOB we use.

This unit is a solid hub version of the stage 3. The hub is solid 8-rivet and the assembly is heat treated for strength and durability. 

Street drivable in 6 puck configuration, but not street friendly due to the rigid hub. Best for drag racing, road racing, pulling, rally and drift. Rated for 480 ft lbs

If you select Z33/Z34 fitment, we will provide you with the Z32TT clutch made to fit with our in house CD009 kits. We chose that clutch specifically to design the kit around. This is a different clutch from the 350Z/370Z clutch, even though you are using that transmission.

We offer a full line replacement parts for our custom XAT / Quarter Master clutches to keep your car on the road! Unlike some other multi disc clutch options (such as HKS), these parts are still available new, and don't have to be shipped over from Japan.

The dropdown menus offer an assortment of options to get only the parts you need. We've also provided example pictures to differentiate what the individual options are!

Please note that the pressure plate and clutch cover are not the same part. The pressure plate looks like the floater disc with an added round angle around it, whereas the clutch cover has the actual cover/diaphragm with it. The bottom of the pressure plate has the same surface as the floater disc, but is thicker with a different shape on top

The base kit includes just replacement discs for your twin Rallye clutch. In most cases, you'll need to replace the discs, the pressure plate, and the floater disc. Depending on the condition of the button flywheel, you might be able to reuse it or have it resurfaced locally.

This is the most aggressive single disk clutch kit from SPEC for manual transmission swapped 1UZ, 2UZ, and 3UZ Toyota/Lexus V8 engines, with a holding power of 670 ft.lbs! So if you make the big power, have nitrous or just like to run it very hard, then this is for you. Some light chatter and aggressive holding are common. Can be street driven if you don't mind the chatter. We strongly recommend opting for one of our twin or triple disc clutches at this power level. "Do it once, do it right!" Features a full-metallic disc with the highest possible friction co-efficient. Street drivable, but not street-friendly. The hub is solid 12-rivet and the assembly is heat treated for strength and durability. Best for extreme street and drag racing.

If you select Z33/Z34 fitment, we will provide you with the Z32TT clutch made to fit with our in house CD009 kits. We chose that clutch specifically to design the kit around.

This is the Spec Stage 3 clutch for manual transmission swapped 1UZ, 2UZ, and 3UZ Toyota/Lexus V8 engines, rated for 480ft lbs. 

Features a carbon semi-metallic 6 puck sprung hub disc that has been the leading puck clutch in drivability, life and torque capacity. 

This unit is designed for street and race cars that require an aggressive but streetable engagement and high torque capacity. The hub is double sprung with spring cover relieves for flexibility and heat treated components for strength and durability

If you select Z33/Z34 fitment, we will provide you with the Z32TT clutch made to fit with our in house CD009 kits. We chose that clutch specifically to design the kit around. This is a different clutch from the 350Z/370Z clutch, even though you are using that transmission.

The SPEC Stage 2 Clutch kit custom made for manual transmission swapped 1UZ, 2UZ, and 3UZ Toyota/Lexus V8 engines holds 398 ft lbs of torque, and is an outstanding upgrade for those with basic mods or even stock powered cars that simply want to be able to hold more power for the future. Features segmented or full faced pure Kevlar disc with steel backing. This lining features excellent drivability like the stage 1, but offers slightly longer life and higher torque capacity. The hub is double sprung with spring cover relieves for flexibility and heat treated components for strength and durability. Best for street, drag, pulling and autocross.

If you select Z33/Z34 fitment, we will provide you with the Z32TT clutch made to fit with our in house CD009 kits. We chose that clutch specifically to design the kit around.

SPEC Clutch Stage 1 kit for manual transmission swapped 1UZ, 2UZ, and 3UZ Toyota/Lexus V8 engines. Good for up to 350 ft lbs of torque. Great "stock replacement" setup for budget swaps! Features an integrally molded carbon kevlar-based, high performance organic lining that offers smooth engagement and excellent life. This lining has an integrally bonded steel backing for strength under high clamp loads and temperatures. The hub is double sprung with spring cover relieves for flexibility and heat treated components for strength and durability. Best for street and many track/off-road applications.

If you select Z33/Z34 fitment, we will provide you with the Z32TT clutch made to fit with our in house CD009 kits. We chose that clutch specifically to design the kit around. This is a different clutch from the 350Z/370Z clutch, even though you are using that transmission.

The SPEC Clutch Stage 2+ kit for manual transmission swapped 1UZ, 2UZ, and 3UZ Toyota/Lexus V8 engines uses a slightly more aggressive disc and is rated at 450 ft lbs of torque. Very streetable driving characteristics like the Stage 1 and 2, but with more holding power. 

Features a multi-friction disc in a full faced configuration with carbon semi-metallic on one side and Kevlar on the other. Bridging the gap between stage 2 and stage 3, the 2-plus offers drivability and engagement quality characteristic of the stage 2, but with a 15-20% higher torque capacity. The hub is double sprung with spring cover relieves for flexibility and heat treated components for strength and durability. Great for street, drag, autocross, road racing, pulling, rally and drift.

If you select Z33/Z34 fitment, we will provide you with the Z32TT clutch made to fit with our in house CD009 kits. We chose that clutch specifically to design the kit around.

When we took a look at the previous generation of adapter plates, all we could see was room for improvement and higher quality. We wanted a plate that would mount PERFECTLY with zero slop. It needed to look good and perform even better. DON'T get stuck with an overvalued, sloppy plate that ends up costing you input shafts and has poor fitment. You can go with a less expensive alternative and end up with broken parts, or you can do it right the first time with us! No complaints with over 5 years of service.

This billet aluminum adapter plate reuses your factory 4 speed auto 1GZ bellhousing (1997-2004). It will require you to cut off the CD009 bellhousing, which gives MUCH more room to work with in most chassis. Alignment of the input shaft becomes dependent on this plate and not the quality of the bell housing cut, so worry not! This isn't like other kits out there. 

2005-2017 bellhousings will not fit with this adapter. Although the GR-to-CD009 adapter plate we offer would bolt up, the thickness spacing is still wrong

Regardless of which clutch you use, you will need to use the Quarter Master throw out bearing. 

With single disc clutch setups, this kit is designed to use our custom flywheel that uses off the shelf "Z32 turbo" (89-96 Nissan 300ZX twin turbo) clutches, which are inexpensive, readily available, and hold power well. 

Please see the listing below for the flywheel needed. Please note that with a single disc clutch, this requires a proprietary flywheel. OUR "OEM STYLE" AND "LIGHTWEIGHT" XAT FLYWHEELS WILL NOT WORK WITH THIS TRANSMISSION. You will need the specific CD009 flywheel made for this application.

The twin disc setups include their own flywheel, but will also need a ring gear for the starter (the OEM auto flex plate). 

Included with purchase on this listing:

• Adapter plate with hardware to install
• Quill tube for mounting the hydraulic throw out bearing
• Pilot bushing adapter, with bushing installed
• Throw out bearing (optionally)

XAT Racing took a hard look at the concept, and decided to go all in with the "Toyota Big-Block" design. These V12s have started becoming more popular over the past few years! This will fit all versions of this transmission: CD001, CD003, CD005, CD008, CD009, JK41A, JK41B, JK40C, 1EA0A, and 1EA0B from the 2003-2008 Nissan 350Z/Fairlady Z, 2009-2020 370Z, Skyline V35 and V36 non-GTR sedan and coupe, and Infiniti G35 and G37 

Our products are CAD designed with OEM blocks and transmissions on professional equipment by industry professionals. No bad measurements, no flame cuts, no warped discs, no nonsense. You should be using a 3/4" master cylinder in tandem with the TOB we use.

This is the missing link for doing the 1GZFE swap, or simply adding a manual transmission to your already badass Toyota Century. Our CNC process for manufacturing the plate results in an extremely precise adapter plate, laser tight tolerances, and a focus on quality that has yielded a product that will produce less wear on the transmission and clutch. The adapter kits come with the needed pilot adapter and bushing as well. This is the tried and true kit from XAT Racing, except no imitations when it comes to Toyota V12 1GZs. Sorry, V12 not included.

You can also use the less expensive RAM throw out bearing with this kit, however we do not support it. You will need to drill and tap the plate at your own risk to mount one.

Looking for a clutch for this adapter plate? 

When we took a look at the previous generation of adapter plates, all we could see was room for improvement and higher quality. We wanted a plate that would mount PERFECTLY with zero slop. It needed to look good and perform even better. DON'T get stuck with an overvalued, sloppy plate that ends up costing you input shafts and has poor fitment. You can go with a less expensive alternative and end up with broken parts, or you can do it right the first time with us! No complaints with over 5 years of service.

This billet aluminum adapter plate reuses your automatic 1UZ, 2UZ or 3UZ bellhousing. (U1 or U2 from the 4 speed and 5 speed autos. 3UZ 6 speed bellhousing will not fit). It will require you to cut off the CD009 bellhousing, which gives MUCH more room to work with in most chassis. Alignment of the input shaft becomes dependent on this plate and not the quality of the bell housing cut, so worry not! This isn't like other kits out there. This will also fit 2UZs, though the kit was designed to use the U1 bellhousing specifically.

Regardless of which clutch you use, you will need to use the Quarter Master throw out bearing. 

With single disc clutch setups, this kit is designed to use our custom flywheel that uses off the shelf "Z32 turbo" (89-96 Nissan 300ZX twin turbo) clutches, which are inexpensive, readily available, and hold power well. 

Please see the listing below for the flywheel needed. Please note that with a single disc clutch, this requires a proprietary flywheel. OUR "OEM STYLE" AND "LIGHTWEIGHT" XAT FLYWHEELS WILL NOT WORK WITH THIS TRANSMISSION. You will need the specific CD009 flywheel made for this application.

The twin disc setups include their own flywheel, but will also need a ring gear for the starter (the OEM auto flex plate). 

Included with purchase on this listing:

• Adapter plate with hardware to install
• Quill tube for mounting the hydraulic throw out bearing
• Pilot bushing adapter, with bushing installed
• Throw out bearing (optionally)

XAT Racing took a hard look at the concept, and decided to go all in with the "Toyota Small-Block" design. These V8s have started becoming overwhelmingly popular over the past few years! This will fit all versions of this transmission: CD001, CD003, CD005, CD008, CD009, JK41A, JK41B, JK40C, 1EA0A, and 1EA0B from the 2003-2008 Nissan 350Z/Fairlady Z, 2009-2020 370Z, Skyline V35 and V36 non-GTR sedan and coupe, and Infiniti G35 and G37 

Our products are CAD designed with OEM blocks and transmissions on professional equipment by industry professionals. No bad measurements, no flame cuts, no warped discs, no nonsense. You should be using a 3/4" master cylinder in tandem with the TOB we use.

This is the missing link for doing the 1UZFE, 2UZFE, or 3UZFE swap, or simply adding a manual transmission to your already existing UZ powered vehicle (LS400, SC400, and GS400 included). Our CNC process for manufacturing the plate results in an extremely precise adapter plate, laser tight tolerances, and a focus on quality that has yielded a product that will produce less wear on the transmission and clutch. The kits being sold by our "competition" are routinely a few thousands off and have sloppy fitting dowel pin holes. We have even seen competitor's products first hand being warped right out of the box! The adapter kits come with the needed pilot adapter and bushing as well. This is the tried and true kit from XAT Racing, except no imitations when it comes to 1UZs..

You can also use the less expensive RAM throw out bearing with this kit, however we do not support it. You will need to drill and tap the plate at your own risk to mount one.

You may also need other manual conversion parts, depending on your chassis. Please keep in mind you may need to use a 3/4" bore master cylinder with this kit. The factory master cylinder may be enough, however it will ultimately depend on your application. The majority of Toyota car manuals have a 5/8" bore master. The optional master cylinder we provide may require further chassis modification to bolt up to your firewall.

The GKTech shifter is great for relocating the shifter fit Lexus SC fitment and MkIV Supra fitment. Should also fit other applications as well, though that will depend on the chassis you're using and where the engine is mounted

Looking for a clutch for this adapter plate?