UZ Series 1UZ 2UZ 3UZ

When we took a look at the previous generation of adapter plates, all we could see was room for improvement and higher quality. We wanted a plate that would mount PERFECTLY with zero slop. It needed to look good and perform even better. DON'T get stuck with an overvalued, sloppy plate that ends up costing you input shafts and has poor fitment. You can go with a less expensive alternative and end up with broken parts, or you can do it right the first time with us! No complaints with over 5 years of service.

This billet aluminum adapter plate reuses your factory 4 speed auto 1GZ bellhousing (1997-2004). It will require you to cut off the CD009 bellhousing, which gives MUCH more room to work with in most chassis. Alignment of the input shaft becomes dependent on this plate and not the quality of the bell housing cut, so worry not! This isn't like other kits out there. 

2005-2017 bellhousings will not fit with this adapter. Although the GR-to-CD009 adapter plate we offer would bolt up, the thickness spacing is still wrong

Regardless of which clutch you use, you will need to use the Quarter Master throw out bearing. 

With single disc clutch setups, this kit is designed to use our custom flywheel that uses off the shelf "Z32 turbo" (89-96 Nissan 300ZX twin turbo) clutches, which are inexpensive, readily available, and hold power well. 

Please see the listing below for the flywheel needed. Please note that with a single disc clutch, this requires a proprietary flywheel. OUR "OEM STYLE" AND "LIGHTWEIGHT" XAT FLYWHEELS WILL NOT WORK WITH THIS TRANSMISSION. You will need the specific CD009 flywheel made for this application.

The twin disc setups include their own flywheel, but will also need a ring gear for the starter (the OEM auto flex plate). 

Included with purchase on this listing:

• Adapter plate with hardware to install
• Quill tube for mounting the hydraulic throw out bearing
• Pilot bushing adapter, with bushing installed
• Throw out bearing (optionally)

XAT Racing took a hard look at the concept, and decided to go all in with the "Toyota Big-Block" design. These V12s have started becoming more popular over the past few years! This will fit all versions of this transmission: CD001, CD003, CD005, CD008, CD009, JK41A, JK41B, JK40C, 1EA0A, and 1EA0B from the 2003-2008 Nissan 350Z/Fairlady Z, 2009-2020 370Z, Skyline V35 and V36 non-GTR sedan and coupe, and Infiniti G35 and G37 

Our products are CAD designed with OEM blocks and transmissions on professional equipment by industry professionals. No bad measurements, no flame cuts, no warped discs, no nonsense. You should be using a 3/4" master cylinder in tandem with the TOB we use.

This is the missing link for doing the 1GZFE swap, or simply adding a manual transmission to your already badass Toyota Century. Our CNC process for manufacturing the plate results in an extremely precise adapter plate, laser tight tolerances, and a focus on quality that has yielded a product that will produce less wear on the transmission and clutch. The adapter kits come with the needed pilot adapter and bushing as well. This is the tried and true kit from XAT Racing, except no imitations when it comes to Toyota V12 1GZs. Sorry, V12 not included.

You can also use the less expensive RAM throw out bearing with this kit, however we do not support it. You will need to drill and tap the plate at your own risk to mount one.

Looking for a clutch for this adapter plate? 

XAT Racing Toyota Lexus 1GZ V12 Lightweight Billet Aluminum 13.5 lb Flywheel for CD009 Nissan Infiniti 6 speed 350Z 370Z G35 G37 Manual Transmission Swaps

For this setup, XAT started completely from scratch, as nothing beats a purpose built billet part from the ground up! As we continue to partner up and offer more and more options for the increasingly popular Nissan 350Z/370Z 6 speed-known to handle over 800 HP at the wheels without opening it up, we continue to bring custom bespoke and billet parts to replace the aged V160 and R154 options. 

These Nissan trannies have been proven that they are a stout and reliable trans that is inexpensive, readily available, and will be for many years to come. Although the early years proved to be troublesome with the CD001, CD003, and CD005 transmissions, by the CD008 and CD009 revisions, shifting has been improved, smoothed out, and solidified. The newer JK40C 370Z transmissions are also reported to have the same internals carried over from the CD009. 

This will fit all versions of this transmission: CD001, CD003, CD005, CD008, CD009, JK41A, JK41B, JK40C, 1EA0A, and 1EA0B Our light weight flywheel is infinitely rebuildable with replaceable friction surface disc, and at just under 14 lbs, it feels right at home both on the street and at the track. Flywheel bolts get torqued to 80 ft lbs. Dont forget to do so in a cross pattern! Single disc clutch options will be anything "off the shelf" that fits the 300ZX turbo (Z32). 

Please email us if you have ANY questions or need assistance with choosing the right clutch for your build! 

** We sell clutch kits to fit this flywheel, ready to go! ** 

As a quick recap: You will need the JZ J3 automatic bellhousing, as well as our adapter kit (or SupraStore's), if you haven't converted already. We also have twin disc QuarterMaster clutches (7.25" and 8.5" twin disc) and flywheels. We offer a QM throw out bearing for fitment. The twin disc clutch kits do NOT use this flywheel, they use a "button flywheel" instead.

W-Series Transmission Adapter for 1UZFE Swap FITS ALL KNOWN W SERIES ALUMINUM HOUSING TRANSMISSIONS

1UZ 2UZ 3UZ R-154 R150 R151 R150F R151F 5 Speed Adapter and Throwout Bearing Kit (also fits 1997-2004 Toyota V12s!)

When we took a look at the previous generation of adapter plates, all we could see was room for improvement and higher quality. We wanted a plate that would mount PERFECTLY with zero slop. It needed to look good and perform even better. DON'T get stuck with an overvalued, sloppy plate that ends up costing you input shafts and has poor fitment. You can go with a less expensive alternative and end up with broken parts, or you can do it right the first time with us! No complaints with over 5 years of service.

This billet aluminum adapter plate reuses your automatic 1UZ, 2UZ or 3UZ bellhousing. (U1 or U2 from the 4 speed and 5 speed autos. 3UZ 6 speed bellhousing will not fit). It will require you to cut off the CD009 bellhousing, which gives MUCH more room to work with in most chassis. Alignment of the input shaft becomes dependent on this plate and not the quality of the bell housing cut, so worry not! This isn't like other kits out there. This will also fit 2UZs, though the kit was designed to use the U1 bellhousing specifically.

Regardless of which clutch you use, you will need to use the Quarter Master throw out bearing. 

With single disc clutch setups, this kit is designed to use our custom flywheel that uses off the shelf "Z32 turbo" (89-96 Nissan 300ZX twin turbo) clutches, which are inexpensive, readily available, and hold power well. 

Please see the listing below for the flywheel needed. Please note that with a single disc clutch, this requires a proprietary flywheel. OUR "OEM STYLE" AND "LIGHTWEIGHT" XAT FLYWHEELS WILL NOT WORK WITH THIS TRANSMISSION. You will need the specific CD009 flywheel made for this application.

The twin disc setups include their own flywheel, but will also need a ring gear for the starter (the OEM auto flex plate). 

Included with purchase on this listing:

• Adapter plate with hardware to install
• Quill tube for mounting the hydraulic throw out bearing
• Pilot bushing adapter, with bushing installed
• Throw out bearing (optionally)

XAT Racing took a hard look at the concept, and decided to go all in with the "Toyota Small-Block" design. These V8s have started becoming overwhelmingly popular over the past few years! This will fit all versions of this transmission: CD001, CD003, CD005, CD008, CD009, JK41A, JK41B, JK40C, 1EA0A, and 1EA0B from the 2003-2008 Nissan 350Z/Fairlady Z, 2009-2020 370Z, Skyline V35 and V36 non-GTR sedan and coupe, and Infiniti G35 and G37 

Our products are CAD designed with OEM blocks and transmissions on professional equipment by industry professionals. No bad measurements, no flame cuts, no warped discs, no nonsense. You should be using a 3/4" master cylinder in tandem with the TOB we use.

This is the missing link for doing the 1UZFE, 2UZFE, or 3UZFE swap, or simply adding a manual transmission to your already existing UZ powered vehicle (LS400, SC400, and GS400 included). Our CNC process for manufacturing the plate results in an extremely precise adapter plate, laser tight tolerances, and a focus on quality that has yielded a product that will produce less wear on the transmission and clutch. The kits being sold by our "competition" are routinely a few thousands off and have sloppy fitting dowel pin holes. We have even seen competitor's products first hand being warped right out of the box! The adapter kits come with the needed pilot adapter and bushing as well. This is the tried and true kit from XAT Racing, except no imitations when it comes to 1UZs..

You can also use the less expensive RAM throw out bearing with this kit, however we do not support it. You will need to drill and tap the plate at your own risk to mount one.

You may also need other manual conversion parts, depending on your chassis. Please keep in mind you may need to use a 3/4" bore master cylinder with this kit. The factory master cylinder may be enough, however it will ultimately depend on your application. The majority of Toyota car manuals have a 5/8" bore master. The optional master cylinder we provide may require further chassis modification to bolt up to your firewall.

The GKTech shifter is great for relocating the shifter fit Lexus SC fitment and MkIV Supra fitment. Should also fit other applications as well, though that will depend on the chassis you're using and where the engine is mounted

Looking for a clutch for this adapter plate? 

For this setup, XAT started completely from scratch, as nothing beats a purpose built billet part from the ground up! As we continue to partner up and offer more and more options for the increasingly popular Nissan 350Z/370Z 6 speed-known to handle over 800 HP at the wheels without opening it up, we continue to bring custom bespoke and billet parts to replace the aged V160 and R154 options. 

These Nissan trannies have been proven that they are a stout and reliable trans that is inexpensive, readily available, and will be for many years to come. Although the early years proved to be troublesome with the CD001, CD003, and CD005 transmissions, by the CD008 and CD009 revisions, shifting has been improved, smoothed out, and solidified. The newer JK40C 370Z transmissions are also reported to have the same internals carried over from the CD009. 

This will fit all versions of this transmission: CD001, CD003, CD005, CD008, CD009, JK41A, JK41B, JK40C, 1EA0A, and 1EA0B Our light weight flywheel is infinitely rebuildable with replaceable friction surface disc, and at just under 14 lbs, it feels right at home both on the street and at the track. Flywheel bolts get torqued to 80 ft lbs. Dont forget to do so in a cross pattern! Single disc clutch options will be anything "off the shelf" that fits the 300ZX turbo (Z32). 

Please email us if you have ANY questions or need assistance with choosing the right clutch for your build! 

** We sell clutch kits to fit this flywheel, ready to go! ** 

As a quick recap: You will need the UZ V8 automatic bellhousing, if you haven't converted already. We also have twin disc QuarterMaster clutches (7.25" and 8.5" twin disc) and flywheels. We offer a QM throw out bearing for fitment. The twin disc clutch kits do NOT use this flywheel, they use a "button flywheel" instead.

Required ARP Flywheel bolts are included with this flywheel!

Our 1UZ / 2UZ / 3UZ series V8 chromoly flywheel is made form some of the hardest, most durable metal we can source for a flywheel.

Our machine shop gets mad every time we do a production run--they go on and on about how hard the alloy is, takes longer to machine, wears out tooling... Well that's great news if you're planning on abusing your V8!!! This flywheel will take some serious abuse without a doubt, and we have proven it ourselves in our personal cars over a length of time.

Weighing in at just 11 LBS, you will instantly notice your V8 rev up and rev down much faster! This equates to a more responsive throttle, getting to the important parts of your powerband, and more efficient engine braking.

Our flywheel utilizes the proven torque holding clutches of the SW20 MR2 TURBO 3S-GTE. We offer clutch setups to suit everything from a stock engine all the way to to 680 FT/LBS with this flywheel!

When installing our flywheel: you will be required to install the OEM automatic bolt guide on the crank before installing the flywheel. This item is curved--the curve needs to face the engine and fit flat on the crank-to-flywheel mating surface. Please see pictures for more information as well. After installing the bolt guide, torque the included ARP bolt kit to 70 FT/LBS using red thread locker/loctite on the bolts, and tightening in a star pattern, not one next to the other. We also recommend tightening down in 2 or 3 goes as well instead of going from finger tight straight to 70 ft lbs.

This flywheel is meant for our W55/W58, R150/R151, R154, KA, and SR transmission adapters. This will NOT work with our CD009 / JK series Nissan 6 speed adapter!

XAT Racing is proud to announce the latest single disc in house custom made flywheel option for our many UZ swap kits! Unlike our OEM style and lightweight chromoly flywheels, these aluminum ones are infinitely rebuildable with a replacement friction surface and hardware (included!). They are also tailor made for the UZ Toyota/Lexus V8s from the ground up, not re-purposed from other flywheels!! This flywheel comes in at just over 9 lbs!!

Our aluminum flywheels will use the same 3S-GTE clutches that the other flywheels and our kits utilize. We have a broad selection of choices, some of which are in stock. We will be happy to help and make recommendations for your application!

This flywheel will work with any of our W55, W56, W58, W59, R150, R151, R154, R155, KA, or SR transmission adapters. This will not work with our CD009 or JK series Nissan 6 speed kits. 

No spacers are required to bolt this on, not even the factory one that goes from the crankshaft to factory flex plate gets reused.

Ring gear is already fit, and friction surface is included with order!